Liquid Ready Mix Colors - ColorFlo™
Solomon Colors ColorFlo™ Liquid Concrete Colors are predispersed iron oxide pigments containing high pigment solids in an aqueous base liquid. The use of ColorFlo™ Liquid Concrete Colors provides an easy handling, dust-free environment for integral coloring of concrete block, concrete pavers, concrete floors, plus vertical precast and poured-in-place concrete construction.
Due to shade variations associated with individual color monitors and printers, we suggest utilization of our literature request form to review an actual ColorFlo™ Liquid Color Brochure. We strongly recommend that a test slab be poured and approved prior to starting the a job. Test slabs should be poured replicating job site conditions. Lower dosage of color and variations in gray cement may effect the final shade.
OVERVIEW OF BENEFITS
Convenient and accurate batch control. Iron oxide liquid colors can be easily pumped at a measured rate to assure accurate color batching. They can also be measured by weight or volume for batching purposes.
Location flexibility. Because of its ability to pump the liquid colors, the dispensing system can be located away from the congestion of your mixers, machines and forklift equipment. Product can be pumped to second-level mixers from ground level, eliminating the need to lift heavy dry pigment to upper floors.
Reallocation of personnel time. Most dispensing systems are automatic and require little attention during operation. This allows you to redistribute manpower to other productive areas.
Cleaner and safer operation. There is no direct handling of dry pigment, resulting in a cleaner and safer environment.
Inventory ease and consolidation. You only need to stock four primary liquid iron oxide colors to create hundreds of standard or custom color blends. (The color chips on the reverse side are just a sampling of liquid colors available to you.)
|
1% loading
|
2% loading
|
3% loading
|
4% loading
|
306
Canvas
Item ID: sollp3061
$45.00 per cu. yd.
|
306
Toffee
Item ID: sollp3062
$59.00 per cu. yd.
|
306
Burlap
Item ID: sollp3063
$69.00 per cu. yd.
|
306
Cinnamon
Item ID: sollp3064
$79.00 per cu. yd.
|
238
Thyme
Item ID: sollp2381
$45.00 per cu. yd.
|
238
Doeskin
Item ID: sollp2382
$59.00 per cu. yd.
|
238
Buttercup
Item ID: sollp2383
$69.00 per cu. yd.
|
238
Marigold
Item ID: sollp2384
$79.00 per cu. yd.
|
338
Earthen
Item ID: sollp3381
$45.00 per cu. yd.
|
338
Rawhide
Item ID: sollp3382
$59.00 per cu. yd.
|
338
Buckskin
Item ID: sollp3383
$69.00 per cu. yd.
|
338
Leather
Item ID: sollp3384
$79.00 per cu. yd.
|
385
Taupe
Item ID: sollp3851
$45.00 per cu. yd.
|
385
Lava
Item ID: sollp3852
$59.00 per cu. yd.
|
385
Buffalo
Item ID: sollp3853
$69.00 per cu. yd.
|
385
Bark
Item ID: sollp3854
$79.00 per cu. yd.
|
|
1% loading
|
2% loading
|
3% loading
|
4% loading
|
242
Sandstone
Item ID: sollp2421
$45.00 per cu. yd.
|
242
Sahara
Item ID: sollp2422
$59.00 per cu. yd.
|
242
Sandalwood
Item ID: sollp2423
$69.00 per cu. yd.
|
242
Nutmeg
Item ID: sollp2424
$79.00 per cu. yd.
|
492
Mauve
Item ID: sollp4921
$45.00 per cu. yd.
|
492
Merlot
Item ID: sollp4922
$59.00 per cu. yd.
|
492
Lilac
Item ID: sollp4923
$69.00 per cu. yd.
|
492
Garnet
Item ID: sollp4924
$79.00 per cu. yd.
|
467
Ash
Item ID: sollp4671
$45.00 per cu. yd.
|
467
Oyster
Item ID: sollp4672
$59.00 per cu. yd.
|
467
Orchid
Item ID: sollp4673
$69.00 per cu. yd.
|
467
Rustique
Item ID: sollp4674
$79.00 per cu. yd.
|
920
Slate
Item ID: sollp9201
$45.00 per cu. yd.
|
920
Smoke
Item ID: sollp9202
$59.00 per cu. yd.
|
920
Charcoal
Item ID: sollp9203
$69.00 per cu. yd.
|
920
Onyx
Item ID: sollp9204
$79.00 per cu. yd.
|
GENERAL GUIDELINES
Color Pigments
| |
Color pigments may be added at any time after aggregates, water, and cement.
|
Aggregates
| |
Pre-wet aggregates before adding color pigments.
|
| |
Use clean aggregates with low soluble salt content.
|
| |
Weigh all aggregates and cement accurately for each batch.
|
Mixing
| |
Mixer should be loaded to a minimum of 40% capacity to insure good color dispersion.
|
| |
DO NOT LOAD the mixer beyond the recommended capacity. OVERLOADING will reduce mixing efficiency.
|
| |
Begin each new truckload with a thoroughly cleaned mixer.
|
| |
Mix for a minimum of 10 minutes AT HIGH SPEED before pouring.
|
| |
Maintain consistent slump at or below four inches.
|
| |
Adding water to concrete during a pour, to allow for the placement of concrete in stages, should be kept to a minimum.
|
Additives
| |
DO NOT use calcium chloride. This product can cause discoloration in the form of light and dark areas in the finished product.
|
| |
The use of lignin in the mix will enhance color dispersion.
|
| |
The use of plasticizers and air entraining products designed for colored concrete production are acceptable.
|
Final Finish
| |
Initial floating should be discontinued as soon as the surface becomes wet. Floating may be resumed after the surface water disappears.
|
| |
The final finish such as broom, swirl, or imprinting may be completed after floating.
|
| |
Do not cover, fog or otherwise attempt to "cure" the slab at this time. Any of these actions will create uneven coloring.
|
| |
Use of a clear non-yellowing breathable UV-stable acrylic cure and seal after a minimum of 24* hours is acceptable. (In locales where high heat and low humidity conditions exist, a non-staining evaporation control and/or sealers may need to be applied sooner)
|
* When conditions are cool or when sub-base or concrete is overly wet, efflorescence may appear on the concrete surface as a white powder. This can be removed before sealing by scrubbing with water and a push broom, pressure washer or a mild acid solution. depending on the age of the concrete. Allow surface to dry completely before sealing.
